Heyu

From Omnia
Jump to navigation Jump to search

heyu

Connect to controller through serial - CM11A interface

heyu info
heyu on a1
heyu dim A2 10
heyu bright A2 10
heyu off a1
heyu status b2

References:

state engine

start state engine:

heyu engine
heyu start  # same as engine
heyu restart
heyu enginestate  # 1 or 0
heyu onstate a1  # or "offstate"
heyu dimstate a1  # or "offstate"
heyu dimlevel a1
heyu stop

installation

mkdir -p ~/.src ; cd ~/.src
wget http://heyu.org/download/heyu-2.10.tar.gz
tar xf heyu-2.10.tar.gz
cd heyu-2.10
sh ./Configure
make
# ... note this will take several minutes!

sudo make install
# select '3' - In directory /etc/heyu  (for system-wide access)
# select '/dev/ttyUSB1'
# configure - auto started by make install
#./install.sh
# add user to dialout group (group write to /dev/ttyUSB1
sudo usermod -a -G dialout kenneth
# verify connection (may need to logout and back in)
heyu info

If you want to PREFIX, you have to manually hack the generated Makefile near the top:

BIN = /usr/local/bin
MAN = /usr/local/man/man1
MAN5 = /usr/local/man/man5

Uninstall:

make uninstall

References:

cm11a connection

dmesg:

usb 4-5: new full speed USB device using ohci_hcd and address 4
usb 4-5: configuration #1 chosen from 1 choice
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
pl2303 4-5:1.0: pl2303 converter detected
usb 4-5: pl2303 converter now attached to ttyUSB1
usbcore: registered new driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver

info

heyu info
# heyu info
starting heyu_relay
04/11 08:52:08  Poll received unknown value (1 bytes), leading byte = a5
Heyu version 2.10
Configuration at /etc/heyu/x10.conf
Powerline interface on /dev/ttyUSB0
Firmware revision Level = 1
Interface battery usage = Unknown
Raw interface clock: Fri, Day 100, 07:52:07
(--> Civil Time: Fri 11 Apr 2014   08:52:07 MDT)
No schedule has been uploaded by Heyu.
Housecode = A
0 = off, 1 = on,               unit  16.......8...4..1
Last addressed device =       0x0000 (0000000000000000)
Status of monitored devices = 0x0000 (0000000000000000)
Status of dimmed devices =    0x0000 (0000000000000000)

init.d

init.d, based off of Jira startup script:

#!/bin/bash

BIN=/usr/local/bin/heyu

case "$1" in
    start)
        $BIN engine
        ;;
    stop)
        $BIN stop
        ;;
    restart)
        $BIN restart
        ;;
    status)
        $BIN enginestate
        ;;
    *)
        echo "Usage: $0 {start|stop|restart|status}"
        exit 1
        ;;
esac

debian init.d:

#!/bin/bash

### BEGIN INIT INFO
# Provides: heyu
# Required-Start: $local_fs $syslog $remote_fs
# Required-Stop: $remote_fs
# Default-Start:  2 3 4 5
# Default-Stop: 0 1 6
# Short-Description: Start heyu service
# Description: Monitor X10 commands
### END INIT INFO

BIN=/usr/local/bin/heyu

case "$1" in
    start)
        $BIN engine
        ;;
    stop)
        $BIN stop
        ;;
    restart)
        $BIN restart
        ;;
    status)
        $BIN enginestate
        ;;
    *)
        echo "Usage: $0 {start|stop|restart|status}"
        exit 1
        ;;
esac

monitor

Monitor

heyu engine
heyu monitor
04/11 20:51:43  sndc addr unit       1 : hu A1  (_no_alias_)
04/11 20:51:43  sndc func           On : hc A
04/11 20:51:48  sndc addr unit       1 : hu A1  (_no_alias_)
04/11 20:51:49  sndc func          Off : hc A
04/11 14:25:52  sndc addr unit       1 : hu A1  (_no_alias_)
04/11 14:25:53  sndc func       Bright : hc A bright %100 [210+]
04/11 14:27:02  sndc addr unit       1 : hu A1  (_no_alias_)
04/11 14:27:03  sndc func       Bright : hc A bright %100 [210+]
04/11 14:27:07  sndc func          Dim : hc A dim %01 [~2]

change cm11a housecode

Change CM11A Housecode

heyu reset [housecode]
heyu reset C
heyu info

issues

Unable to send address bytes

If you got the error, like this:

tarting heyu_relay
Unable to send address bytes

maybe the X10 computer interface is not connected properly. If you are using USB-RS232 converter, try to plug-unplug the converter to solve this "freezing" problem.

References:

keywords